CBoardENoses.h

Go to the documentation of this file.

/* +------------------------------------------------------------------------+
   |                     Mobile Robot Programming Toolkit (MRPT)            |
   |                          http://www.mrpt.org/                          |
   |                                                                        |
   | Copyright (c) 2005-2018, Individual contributors, see AUTHORS file     |
   | See: http://www.mrpt.org/Authors - All rights reserved.                |
   | Released under BSD License. See details in http://www.mrpt.org/License |
   +------------------------------------------------------------------------+ */

#ifndef CBoardENoses_H
#define CBoardENoses_H

#include <mrpt/comms/CInterfaceFTDI.h>
#include <mrpt/comms/CSerialPort.h>
#include <mrpt/hwdrivers/CGenericSensor.h>

#include <mrpt/obs/CObservationGasSensors.h>
#include <mrpt/config/CConfigFileBase.h>
#include <memory>  // unique_ptr

namespace mrpt::hwdrivers
{
/** A class for interfacing an e-Noses via a FTDI USB link.
 *  Implemented for the board v1.0 designed by 2007 @ ISA (University of
 * Malaga).
 *
 *  \code
 *  PARAMETERS IN THE ".INI"-LIKE CONFIGURATION STRINGS:
 * -------------------------------------------------------
 *   [supplied_section_name]
 *    USB_serialname=ENOSE001   // USB FTDI pipe: will open only if COM_port_*
 * are not set or empty
 *
 *    COM_port_WIN = COM1       // Serial port to connect to.
 *    COM_port_LIN = ttyS0
 *
 *    COM_baudRate = 115200
 *
 *    ; 3D position (in meters) of the master +slave eNoses
 *    enose_poses_x=<MASTER X> <SLAVE#1 X> <SLAVE#2 X> <SLAVE#3 X>...
 *    enose_poses_y=<MASTER Y> <SLAVE#1 Y> <SLAVE#2 Y> <SLAVE#3 Y>...
 *    enose_poses_z=<MASTER Z> <SLAVE#1 Z> <SLAVE#2 Z> <SLAVE#3 Z>...
 *
 *    ; 3D pose angles (in degrees) of the master +slave eNoses
 *    enose_poses_yaw=<MASTER YAW> <SLAVE#1 YAW> <SLAVE#2 YAW> <SLAVE#3 YAW>...
 *    enose_poses_pitch=<MASTER PITCH> <SLAVE#1 PITCH> <SLAVE#2 PITCH> <SLAVE#3
 * PITCH>...
 *    enose_poses_roll=<MASTER ROLL> <SLAVE#1 ROLL> <SLAVE#2 ROLL> <SLAVE#3
 * ROLL>...
 *
 *  \endcode
 *
 * \ingroup mrpt_hwdrivers_grp
 */
class CBoardENoses : public mrpt::hwdrivers::CGenericSensor
{
    DEFINE_GENERIC_SENSOR(CBoardENoses)

   protected:
    /** A copy of the device serial number (to open the USB FTDI chip)
     */
    std::string m_usbSerialNumber;
    mrpt::Clock::duration initial_timestamp;
    bool first_reading;

    /** If not an empty string (default), will open that serial port, otherwise
     * will try to open USB FTDI device "m_usbSerialNumber" */
    std::string m_COM_port;
    /** Default=115200 */
    unsigned int m_COM_baud;

    // Only one of these two streams will be !=nullptr and open for each
    // specific eNose board!
    /** FTDI comms pipe (when not in serial port mode) */
    std::unique_ptr<mrpt::comms::CInterfaceFTDI> m_stream_FTDI;
    /** Serial port comms */
    std::unique_ptr<mrpt::comms::CSerialPort> m_stream_SERIAL;

    /** The 3D pose of the master + N slave eNoses on the robot (meters &
     * radians) */
    std::vector<float> enose_poses_x, enose_poses_y, enose_poses_z,
        enose_poses_yaw, enose_poses_pitch, enose_poses_roll;

    /** Tries to connect to the USB device (if disconnected).
     * \return nullptr on error, otherwise a stream to be used for comms.
     */
    mrpt::io::CStream* checkConnectionAndConnect();

    /** See the class documentation at the top for expected parameters */
    void loadConfig_sensorSpecific(
        const mrpt::config::CConfigFileBase& configSource,
        const std::string& section);

   public:
    /** Constructor
     * \param serialNumberUSBdevice The serial number (text) of the device to
     * open.
     *  The constructor will try to open the device. You can check if it failed
     * calling "isOpen()".
     */
    CBoardENoses();

    /** Set the active chamber (afected by poluted air) on the device
     * \return true on success, false on communications errors or device not
     * found.
     */
    bool setActiveChamber(unsigned char chamber);

    /** Query the firmware version on the device (can be used to test
     * communications).
     * \return true on success, false on communications errors or device not
     * found.
     */
    bool queryFirmwareVersion(std::string& out_firmwareVersion);

    /** Request the master eNose the latest readings from all the eNoses.
     *  The output observation contains a valid timestamp and 3D positions if
     * "loadConfig" has been called previously.
     * \return true if OK, false if there were any error.
     */
    bool getObservation(mrpt::obs::CObservationGasSensors& outObservation);

    // See docs in parent class
    void doProcess();

    /** Tries to open the camera, after setting all the parameters with a call
     * to loadConfig.
     *  \exception This method must throw an exception with a descriptive
     * message if some critical error is found.
     */
    virtual void initialize();

    /** If not an empty string, will open that serial port, otherwise will try
     * to open USB FTDI device "m_usbSerialNumber"
     *  The default is an empty string. Example strings: "COM1", "ttyUSB0", ...
     */
    inline void setSerialPort(const std::string& port) { m_COM_port = port; }
    inline std::string getSerialPort() const { return m_COM_port; }
    /** Set the serial port baud rate (default: 115200) */
    inline void setSerialPortBaud(unsigned int baud) { m_COM_baud = baud; }
    inline unsigned int getSerialPortBaud() const { return m_COM_baud; }
};  // end of class
}  // namespace mrpt::hwdrivers
#endif