CLMS100eth.h

Go to the documentation of this file.

/* +------------------------------------------------------------------------+
   |                     Mobile Robot Programming Toolkit (MRPT)            |
   |                          http://www.mrpt.org/                          |
   |                                                                        |
   | Copyright (c) 2005-2017, Individual contributors, see AUTHORS file     |
   | See: http://www.mrpt.org/Authors - All rights reserved.                |
   | Released under BSD License. See details in http://www.mrpt.org/License |
   +------------------------------------------------------------------------+ */
 
#ifndef CLMS100ETH_H
#define CLMS100ETH_H
 
#include <mrpt/hwdrivers/C2DRangeFinderAbstract.h>
#include <mrpt/comms/CClientTCPSocket.h>
 
namespace mrpt
{
namespace hwdrivers
{
/** This "software driver" implements the communication protocol for interfacing
*a SICK LMS100 laser scanners through an ethernet controller.
        *   This class does not need to be bind, i.e. you do not need to call
*C2DRangeFinderAbstract::bindIO.
        *   Connection is established when user call the turnOn() method. You can
*pass to the class's constructor the LMS100 's ip address and port.
        *   Device will be configured with the following parameters :
        * - Start Angle : -45 deg (imposed by hardware)
        * - Stop Angle : +225 deg (imposed by hardware)
        * - Apperture : 270 deg (imposed by hardware)
        * - Angular resolution : 0.25 deg
        * - Scan frequency : 25 Hz
        * - Max Range : 20m (imposed by hardware).
        *
        * <b>Important note:</b> SICK LMS 1xx devices have two levels of
*configuration. In its present implementation, this class only handles one of
*them, so
        *    <b>before using this class</b>, you must "pre-configure" your scanner
*with the SICK's software "SOAP" (this software ships with the device),
        *    and set the framerate with this software. Of course, you have to
*pre-configure the device just once, then save that configuration in its flash
*memory.
        *
        * To get a laser scan you must proceed like that :
        * \code
        *     CLMS200Eth laser(string("192.168.0.10"), 1234);
        *     laser.turnOn();
        *     bool isOutObs, hardwareError;
        *     CObservation2DRangeScan outObs;
        *     laser.doProcessSimple(isOutObs, outObs, hardwareError);
        * \endcode
        *
        * The sensor pose on the vehicle could be loaded from an ini configuration
*file with :
        *  \code
        *  PARAMETERS IN THE ".INI"-LIKE CONFIGURATION STRINGS:
        * -------------------------------------------------------
        *   [supplied_section_name]
        *         ip_address = 192.168.0.50 ;a string wich is the SICK's ip adress
*(default is 192.168.0.1)
        *   TCP_port = 1234                     ; an integer value : the tcp ip port on wich the
*sick is listening (default is 2111).
        *   pose_x=0.21 ; Laser range scaner 3D position in the robot (meters)
        *   pose_y=0
        *   pose_z=0.34
        *   pose_yaw=0  ; Angles in degrees
        *   pose_pitch=0
        *   pose_roll=0
        *  \endcode
        * This class doesn't configure the SICK LMS sensor, it is recomended to
*configure the sensor via the
* the SICK software : SOPAS.
        * \note This class was contributed by Adrien Barral - Robopec (France)
* \ingroup mrpt_hwdrivers_grp
        */
class CLMS100Eth : public C2DRangeFinderAbstract
{
        DEFINE_GENERIC_SENSOR(CLMS100Eth)
   public:
        /** Constructor.
                * Note that there is default arguments, here you can customize IP Adress
         * and TCP Port of your device.
                */
        CLMS100Eth(
                std::string _ip = std::string("192.168.0.1"),
                unsigned int _port = 2111);
        /** Destructor.
                * Close communcation with the device, and free memory.
                */
        virtual ~CLMS100Eth();
        /** This function acquire a laser scan from the device. If an error occured,
         * hardwareError will be set to true.
                * The new laser scan will be stored in the outObservation argument.
                *
                * \exception This method throw exception if the frame received from the
         * LMS 100 contain the following bad parameters :
                *  * Status is not OK
                *  * Data in the scan aren't DIST1 (may be RSSIx or DIST2).
                */
        void doProcessSimple(
                bool& outThereIsObservation,
                mrpt::obs::CObservation2DRangeScan& outObservation,
                bool& hardwareError);
 
        /** This method must be called before trying to get a laser scan.
                */
        bool turnOn();
        /** This method could be called manually to stop communication with the
         * device. Method is also called by destructor.
                */
        bool turnOff();
 
        /** A method to set the sensor pose on the robot.
                * Equivalent to setting the sensor pose via loading it from a config
         * file.
                */
        void setSensorPose(const mrpt::poses::CPose3D& _pose);
 
        /** This method should be called periodically. Period depend on the
         * process_rate in the configuration file.
                */
        void doProcess();
 
        /** Initialize the sensor according to the parameters previously read in the
         * configuration file.
                */
        void initialize();
 
   private:
        std::string m_ip;
        unsigned int m_port;
        mrpt::comms::CClientTCPSocket m_client;
        bool m_turnedOn;
        std::string m_cmd;
        bool m_connected;
        unsigned int m_scanFrequency;  // hertz
        double m_angleResolution;  // degrees
        double m_startAngle;  // degrees
        double m_stopAngle;  // degrees
        mrpt::poses::CPose3D m_sensorPose;
        double m_maxRange;
        double m_beamApperture;
 
        void generateCmd(const char* cmd);
        bool checkIsConnected();
        bool decodeLogIn(char* msg);
        bool decodeScanCfg(std::istringstream& stream);
        bool decodeScanDataCfg(std::istringstream& stream);
        bool decodeScan(
                char* buf, mrpt::obs::CObservation2DRangeScan& outObservation);
        void sendCommand(const char* cmd);
        void roughPrint(char* msg);
 
   protected:
        /** Load sensor pose on the robot, or keep the default sensor pose.
                */
        void loadConfig_sensorSpecific(
                const mrpt::utils::CConfigFileBase& configSource,
                const std::string& iniSection);
};
}
}
#endif  // CLMS100ETH_H